Placement place selection and quality are key factors in determining the best placement run. Most shoppers don't have a plan and go with the suggestions of the expert. It is important to be aware of your placing needs and discuss them with the expert.
These are the most important things to remember:
Window air conditioner
The window air conditioner should be mounted on the window to allow cool air to settle down and create its cool airflow cycle. If an opening exists in the wall that allows for the conditioner's installation, it is better to choose the same location.
1.5 window sizes are dependent on star rating in 5 stars. The condenser volume is increased by increasing the depth. Several brands offer window sizes that are smaller than 1.5. Some have reduced the capacity of others. If this is the trouble, it is necessary to adjust the window ere you request or pass. This can be done by including a wooden or aluminum panel to secure installation on all sides. If it is not possible, the placing specialist will place the discussion on the two sides and then fill in space on the third with cardboard insulation. In the future, this could be a source of vibration.
Condenser cooling is achieved by sucking air from three sides. If the gap is smaller than the manufacturer recommends, condenser efficiency will be reduced. Hitachi recommends 200 mm for the perfect and left sides and 100 mm for the top. This requirement is not found in many places where air conditioners are placed.
The air conditioner should be placed with a 10mm gap at the front bottom to ensure condensate flows smoothly to the drainpipe. You will have rust issues in 4-6 years.
Avoid direct sunlight hitting the condenser. This will cause poor cooling and reduce efficiency. Instead, it is better to place a sunshade over the window air conditioner.
Split air conditioner
It is important to identify the location for placing the indoor and outdoor systems. In addition, it is important to choose the best site.
- The condenser should be accessible from any window, balcony, or platform that allows for cleaning and servicing. The outdoor condenser's performance will be affected if there is direct sunlight. If possible, cover it with a sunshade.
- To ensure adequate airflow, the placing expert should ensure that there is a gap between the wall of the outdoor system and the wall.
Two pipes of refrigerant are connected to the outdoor system. One brings the air to cool, and the other removes the cool air from the indoor system.
It is important to ensure that proper insulation is installed. Otherwise, condensation can occur during service, which could lead to water-dropping and loss of efficiency.
- Condensate from indoor systems must be collected in the drain pad. Otherwise, it can cause water leakage and wall damage that will require extensive repairs.
Mounting the indoor system on the wall should be done so that airflow does not flow towards the bedroom's main door. As shown in the image below, it is preferred to place the indoor system on the wall.
Final measurements and testing
After the placing has been completed, test the following -
Voltage input
- The power consumed by the compressor when it is running and when it is not. The nameplate of the compressor will indicate the current drawn when it is running. It shall not exceed 6% plus or minus 6.
- The temperature on the suction side and the outflow side.
These measurements can be used to evaluate the service after it is completed. For instance, if the power consumption for a given month is higher than that of the previous year, the air conditioner may require servicing. Therefore, keeping track of these parameters will be helpful.
Maintenance of your air conditioner
Whirlpool ac price in BD require regular maintenance. This is mainly to clean the unit and check for the current draw. It also indicates whether the gas pressure has been maintained as it was originally filled. Inadequate maintenance can result in less cooling and higher power consumption.
Air conditioner servicing should not be done without your supervision.
Ensure that the coils are cleaned to the highest standards. Make sure you observe the cleaning process when booking maintenance. Unfortunately, there is no other preventive maintenance program for an air conditioner except cleaning.
Gas leakage
After three to four years of service, rubber mountings and rubber parts used for securing purposes may deteriorate. A test can be performed when the service is completed.
Brazing gas leakage repair can be dangerous. If not done properly, heat could cause other joints to loosen. This happens often.
Insulation
As loss of insulation can result in reduced cooling, increased power consumption, and water dripping from your air conditioner, makes sure you maintain the insulation of the connecting pipes. Ask the expert to inspect insulation every time you have it serviced.
Conclusion
While it is essential to purchase the right product, it is equally important to ensure that the product is properly placed and maintained. For instance, a Samsung ac price in Bangladesh that is well installed and maintained can provide the best cooling while consuming less power.
Tag:
Comments
Post a Comment